How to change the water faucet quickly and easily, no need to call a repairman!

Drains are considered one of the most important elements in the home, especially as they will affect various activities.

This is because clean water is used for many activities in the home, from cooking and washing clothes to the MCK process.

Therefore, the need for clean water at home, whether using PAM water or groundwater sources, is very essential.

However, not everyone can predict whether there will be damage to the home's water supply regulator.

One very sensitive part is the damage to the water faucet, even the faucet is broken and cannot be repaired.

As a result, you have to replace the faucet in your home with a new one so that your water needs are met.

So, what's a quick and easy way to replace a faucet without having to call a handyman?

Check out the steps and how-to in full below!

Tools required

Before you know how to replace a water faucet, there's some equipment you'll need, including:

1. Tube lock

2. Pipe insulation

3. New faucet

4. Soldering tape

5. Gloves

How to change a water tap quickly and easily

You can follow the easy steps as follows:

1. Turn off the water

Before replacing a damaged faucet, it is a good idea to shut off all streams and waterways in the home.

The way you can do this is to rotate the water pipe clockwise to stop this water pipe.

Do it slowly at this point so that no water flows back from the faucet, or you can also completely shut off the water lines if there are no important activities in the house.

2. Open the water tap

How to replace the second water faucet, you can do this by opening the water faucet you want to replace in a specific part.

Sometimes there are faucets that just need to be turned to open, but there are also those that use screws.

You need to remove these screws so that the process of opening the water tap goes faster and smoother.

3. Clean the water tap

After that, the next way to replace the water faucet is to clean the dirt on the side of the faucet.

In general, when the faucet is broken or the water faucet does not work, there must be dirt accumulated for a long time and affecting the cleanliness of the water.

To clean the faucet, the way you can do is to use a putty knife.

When cleaning the water faucet, make sure that there are no fungi and rust on the corners of the surface.

4. Install the new putty

Next, how to replace the water faucet Next, you can install new putty if the water faucet is not used with the bracket plate or rubber bracket.

It's a good idea to apply the paste to the water tap holder and then press it slowly until it grips the tool.

5. Install the new seat plate and faucet

After cleaning and puttying perfectly, you can install the new faucet holder plate.

Fortunately, there are now many faucets that are easier in terms of aspect and installation.

Just follow the instructions, so your water tap will work perfectly.

6. Install the cover ring and faucet holder

If your faucet uses screws, tighten each bolt to the mounting plate with the nuts and cap washers.

You should also tighten the faucet in the middle with the ring nut cap.

Don't forget to pay attention to the instructions from the faucet manufacturer.

7. Clean up the rest of the water faucet replacement work

Before finishing how to replace a water faucet, you have to clean up the rest of the work, especially on the surface of the faucet.

For example, the rest of the putty and some other dirt. If you see a loose faucet connection, use putty or sealant to strengthen it.

8. Turn on the water line

The method of replacing the water faucet has been completely completed, and it has been completely installed.

Therefore, you can now run the water lines in the house and then run the pipes optimally.

Make sure there are no leaks or remaining water drops when you turn on the faucet. If it's still there, turn it off first so nothing drips.

These are some steps on how to replace a water faucet that you can easily do from home.